In-Situ Polymerization of UHMWPE Using Bi-Supported Ziegler-Natta Catalyst of MoS2 Oxide/MgCl2 (Ethoxide Type)/TiCl4/TiBA: Study of Thermo-Mechanical Properties of System

Amini, Majed; Ramazani S.A, Ahmad; Kheradmand, Amanj

doi:10.22034/ijnc.2019.33520

Document Type : Research Paper

Authors

¹ Chemical & Petroleum Engineering Department Sharif University of Technology, Tehran, Iran

² chemical and oil engineering department, Sharif university of technology, Tehran, Iran

³ Chemical & Petroleum Engineering Department Sharif University of Technology

https://doi.org/10.22034/ijnc.2019.33520

Abstract

The use of UHMWPE has attracted the attention of many researchers and industries. The aim of the present work is to fabricate UHMWPE/MoS2-Oxide nano-composites using in-situ polymerization. For this purpose, modified molybdenum disulfide was used. In order to perform the polymerization, a Ziegler-Natta catalytic system, with MoS2-Oxide and magnesium Ethoxide as support, was used. In order to fabricate nano-composites with different filler percentages, the length of polymerization was varied while other parameters were constant. A significant increase in some of the mechanical properties such as modulus and yield stress confirms the effectiveness of interactions between the nano-particles and the matrix. Thermal properties of the obtained nano-particles were analyzed by DSC and TGA analysis. Results of these analyses indicate an increase in crystallinity, melting temperature and improvement in thermal stability of the samples. Mechanical properties analysis indicates a significant increase in the modulus and tensile strength of nano-composites containing filler compared with pure polymer.

Keywords

References

[1] P. Joensen, R. F. Frindt, S. R. Morrison, Mater. Res. Bull., 21, 457 (1986).

[2] Uni O. Aqueous Suspension and Characterization of Chemically Modified Graphene Sheets 2008:6592–4.

[3] M. Amini M, A. ARS, M. Faghihi, S. Fattahpour, Preparation of nanostructured and Nanosheets of MoS 2 oxide using ox- idation method. Ultrason - Sonochemistry 2017.

[4] R. Rosentsveig, A. Gorodnev, N. Feuerstein, H. Friedman, A. Zak, N. Fleischer, et al. Tribol. Lett., 36, 175 (2009).

[5] Z. K. Su, Y. H. Cui, X. H. Tang, Q. Zhou, Z. H. Liu, Chinese. J. Chem., 26, 575 (2008).

[6] L. T. Eunju, E. L. Kee, S. J. Jong, B. Y. Kyung, J. Am. Chem. Soc., 130, 6534 (2008).

[7] S. M. Paek, H. Jung, M. Park, J. K. Lee, J. H. Choy, Chem. Mater., 17, 3492 (2005).

[8] M. Mirzaei, Zeitschrift. Fur. Naturforsch. - Sect A. J. Phys. Sci., 65, 844 (2010).

[9] J. Tannous, F. Dassenoy, I. Lahouij, T. Le Mogne, B. Vacher, A. Bruhács, et al. Tribol. Lett., 41, 55 (2011).

[10] H. I. Karunadasa, E. Montalvo, Y. Sun, M. Majda, J. R. Long, C. J. Chang, Sci., 335, 698 (2012).

[11] M. Wang, G. Li, H. Xu, Y. Qian, J. Yang, A. C. S. Appl. Mater. Interfaces.,5, 1003 (2013).

[12] F. Maugé, J. Lamotte, N. S. Nesterenko, O. Manoilova, A. A. Tsyganenko, Catal. Today., 70, 271 (2001).

[13] Q. Farhad, J. Ind. Eng. Chem., 5, 1 (2015).

[14] S. C. Shi, J. Y. Wu, T. F. Huang, Opt. Quantum. Electron., 48, 474 (2016).

[15] Rong J, Sheng MIA, Li H, Ruckenstein ELI. Po lye t hy I ene- Pa I y g ors kite Na nocom p 0s it e Prepared via in situ Coordinated Polymerization n.d.;2:658–65.

[16] M. Amini, et al. Materials Today: Proceedings 5.7 (2018): 15613-15619.

[17] P. Zapata, R. Quijada, C. Covarrubias, E. Moncada, J. Retuert, D. Lee, et al. Appl. Clay. Sci., 113, 457 (2008).

[18] A. Dashti, A. Ramazani SA, Y. Hiraoka, S. Y. Kim, T. Taniike, Macromol. Symp., 285, 52 (2009).

[19] M. Shafiee, A. Ramazani AS, H. Bahrami, A. Kheradmand, R. S. M., 11, 55 (2014).

[20] M. Amini, et al. Polymers for Advanced Technologies (2018).

[21] A. Kheradmand, A. Ramazani S.A., F. Khorasheh, M. Baghalha, H. Bahrami, Polym. Adv. Technol., 26, 315 (2015).

[22] H. Bahrami, A. Ramazani AS, A. Kheradmand, M. Shafiee, H. Baniasadi, Adv. Polym. Technol. 34, 1 (2015).

[23] J. Chen, F. Maug, E. l. J. Fallah, L. Oliviero, J. Catal., 320,170 (2014).

[24] S. K. Ghosh, C. Srivastava, S. Nath, J. P. Celis, Int. J. Electrochem., 20, 1 (2013).

[25] M. Del Valle, J. Cruz-Reyes, M. Avalos-Borja, S. Fuentes, Catal. Letters., 54, 59 (1998).

[26] B. C. Helmly, W. E. Lynch, D. A. Nivens, Spectrosc. Lett., 40, 483 (2007).

[27] S. Kazuo, T. S. Yoshiharu Doi, Makromol. Chem.,189, 1531 (1988).

[28] G. H. Zohuri, R. Jamjah, S. Ahmadjo, J. Appl. Polym. Sci.,100, 2220 (2006).

[29] P. Pokasermsong, P. Praserthdam, Eng. J., 13, 57 (2009).

[30] H. Baniasadi, A. Ramazani S.A., S. Javan Nikkhah, Mater. Des., 31, 76 (2010).

[31] J. R. H. Li, Z. Jing, X. Hong, M. Sheng, J. Appl. Polym. Sci., 82, 1829 (2001).

International Journal of New Chemistry

In-Situ Polymerization of UHMWPE Using Bi-Supported Ziegler-Natta Catalyst of MoS2 Oxide/MgCl2 (Ethoxide Type)/TiCl4/TiBA: Study of Thermo-Mechanical Properties of System

References

References

Volume 6, Issue 2
April 2019
Pages 87-108

In-Situ Polymerization of UHMWPE Using Bi-Supported Ziegler-Natta Catalyst of MoS2 Oxide/MgCl2 (Ethoxide Type)/TiCl4/TiBA: Study of Thermo-Mechanical Properties of System

References

References

Volume 6, Issue 2April 2019Pages 87-108

Volume 6, Issue 2
April 2019
Pages 87-108